Home
Setup Wizard
The Setup Wizard is a useful and easy utility to help setup the DI-624 to quickly connect to your ISP (Internet Service Provider) with only a few steps required. It will guide you step by step to configure the password, time, WAN, and Wireless settings of your DI-624.
 
Wireless Settings
Wireless Settings are settings for the (Access Point) Portion of the Wireless Router. Allow you to change the wireless settings to fit an existing wireless network or to customize your wireless network.
 
SSID
Service Set Identifier (SSID) is the name designated for a specific wireless local area network (WLAN). The SSID's factory default setting is "default". The SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network.
 
Channel
Indicates the channel setting for the DI-624. By default the channel is set to 6. The Channel can be changed to fit the channel setting for an existing wireless network or to customize the wireless network.  The Auto setting can be selected to allow the DI-624 to choose the channel with the least amount of interference.

Note: Super G with Dynamic Turbo mode only operates in Channel 6.

 
Super G
Super G is a group of performance enhancement features that increase end user application throughput in an 802.11g network. Super G is backwards compatible to standard 802.11g devices. For top performance, all wireless devices on the network should be Super G capable. Select either Disabled, Super G without Turbo, Super G with Dynamic Turbo.

Disabled - Standard 802.11g support, no enhanced capabilities.
Super G without Turbo - Capable of Packet Bursting, FastFrames, Compression, but no Turbo mode.
Super G with Dynamic Turbo - Capable of Packet Bursting, FastFrames, Compression, and Dynamic Turbo. This setting is backwards compatible with non-Turbo (legacy) devices. Dynamic Turbo mode is only enabled when all devices on the wireless network are Super G with Dynamic Turbo enabled.
 
Extended Range Mode
Extended Range Mode helps reduce dead spots by improving the reception algorithm, which allows your wireless clients to associate with the DI-624 at farther distances. Select either Enabled or Disabled.

 
802.11g Only Mode
Enable this mode if your network is made up of purely 802.11g devices. If you have both 802.11b and 802.11g wireless clients, Disable this mode.
 
SSID Broadcast
Select Disabled if you would not like the SSID of your wireless network to be broadcasted by the DI-624.  If this option is Disabled, the SSID of the DI-624 will not be seen by Site Survey utilities so your wireless clients will have to know the SSID of your DI-624 in order to connect to it.
 
Authentication
For added security on the wireless network, when enabling Encryption, the Authentication type can also be selected. If Shared Key is selected, the Access Point will not be seen on the wireless network except to the wireless clients that share the same WEP key with MAC Addresses allowed access as specified in Filter List. If Open System is chosen, only the wireless clients with the same WEP key will be able to communicate on the wireless network, but the Access Point will be visible to all devices on the network. The default value for Authentication is set to "Open System".
 
WEP
Wired Equivalent Protocol (WEP) is a wireless security protocol for Wireless Local Area Networks (WLAN). WEP provides security by encrypting the data that is sent over the WLAN. The DI-624 supports 2 levels of WEP Encryption: 64Bit encryption and 128Bit encryption. WEP is disabled by default. The WEP setting can be changed to fit an existing wireless network or to customize your wireless network.
 
Key Type
The Key Types that are supported by the DI-624 are HEX (Hexadecimal) and ASCII (American Standard Code for Information Interchange.) The Key Type can be changed to fit an existing wireless network or to customize your wireless network.
 
KEYS
Keys 1-4 allow you to easily change wireless encryption settings to maintain a secure network. Simply select the specific key to be used for encrypting wireless data on the network.
 
WPA
Wi-Fi Protected Access authorizes and authenticates users onto the wireless network. WPA uses stronger security than WEP and is based on a key that changes automatically at a regular interval. This mode requires a RADIUS server in the network.
 
WPA-PSK
Pre-Shared Key mode means that the wireless client and the router must have the same passphrase in order to establish the wireless connection. A RADIUS server is not required with PSK.
 
WAN Settings
WAN (wide area network) Settings are settings that are used to connect to your ISP (Internet Service Provider). The WAN settings are provided to you by your ISP and often times referred to as "public settings". Please select the appropriate option for your specific ISP.
 

WAN - Dynamic IP Address
Select this option if your ISP (Internet Service Provider) provides you an IP address automatically. Cable modem providers typically use dynamic assignment of IP Address.

Host Name - (optional) The Host Name field is optional but may be required by some Internet Service Providers. The default host name is the model number of the device.

MAC Address - (optional) The MAC (Media Access Control) Address field is required by some Internet Service Providers (ISP). The default MAC address is set to the MAC address of the WAN interface in the device. You can use the "Clone MAC Address" button to automatically copy the MAC address of the Ethernet Card installed in the computer used to configure the device. It is only necessary to fill the field if required by your ISP.

 

WAN - Static IP Address
If required by your ISP (Internet Service Provider) select this option to configure the device with the static IP Address information. Enter in the IP address, subnet mask, gateway address, and DNS (domain name server) address(es) provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which are four IP octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.

Example: 192.168.100.100

 

WAN - PPPoE
Select this option if your ISP requires you to use a PPPoE (Point to Point Protocol over Ethernet) connection. DSL providers typically use this option. Select Dynamic PPPoE to obtain an IP address automatically for your PPPoE connection (used by majority of PPPoE connections). Select Static PPPoE to use a static IP address for your PPPoE connection.

User Name - Enter your PPPoE username.
Password - Enter your PPPoE password.
Service Name - If your ISP uses a service name for the PPPoE connection, enter the service name here. (optional)

Example:@earthlink.net

IP Address - This option is only available for Static PPPoE. Enter in the static IP address for the PPPoE connection.

Primary DNS Address - Primary DNS (Domain Name Server) IP provided by your ISP.
Secondary DNS Address - optional
Maximum Idle time - The amount of time of inactivity before the device will disconnect your PPPoE session. Enter a Maximum Idle Time (in minutes) to define a maximum period of time for which the Internet connection is maintained during inactivity. If the connection is inactive for longer than the defined Maximum Idle Time, then the connection will be dropped. Either set the value for idle time to zero or enable Auto-reconnect to disable this feature.
Auto-reconnect - If enabled, the device will automatically connect to your ISP after your unit is restarted or when the connection is dropped.

 
LAN Settings
These are the IP settings of the LAN (Local Area Network) interface for the device. These settings may be referred to as "private settings". You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet. The default IP address is 192.168.0.1 with a subnet mask of 255.255.255.0.
IP Address: IP address of the DI-624, default is 192.168.0.1.
Subnet Mask: Subnet Mask of DI-624, default is 255.255.255.0.
Local Domain Name: (optional) Enter in the local domain name for the network.
 
DNS Relay
When DNS Relay is enabled, the router will play a role as DNS server that send request to ISP DNS server and cache the information for later access. When DNS relay is disabled, the computer will pull information from ISP DNS server.
 
DHCP Server
DHCP stands for Dynamic Host Control Protocol. The DHCP server gives out IP addresses when a device is starting up and request an IP address to be logged on to the network. The device must be set as a DHCP client to "Obtain the IP address automatically". By default, the DHCP Server is enabled in the unit. The DHCP address pool contains the range of the IP address that will automatically be assigned to the clients on the network.
Starting IP address - The starting IP address for the DHCP server's IP assignment.
Ending IP address - The ending IP address for the DHCP server's IP assignment.
Lease Time - The length of time for the IP lease.

DHCP client computers connected to the unit will have their information displayed in the DHCP Client Table. The table will show the Host Name, IP Address, MAC Address, and Expired Time of the DHCP lease for each client computer.

 
Static DHCP
Static DHCP allows the router to assign the same IP address information to a specific computer on the local network. The specified computer will get the same DHCP IP address information everytime it is turned on. No other computer on the local network will receive the specified static DHCP address except for the configured computer. Static DHCP is very helpful when used for server computers on the local network that are hosting applications such as Web and FTP.