| Home |
| |
Setup Wizard
The Setup Wizard is a useful and easy utility
to help setup the DSL-G604T to quickly connect to your ISP (Internet Service
Provider) with only a few steps required. It will guide you step by step
to configure time zone, and WAN settings of your DSL-G604T. The
Setup Wizard is a helpful guide for first time users to the DSL-G604T. |
| |
Wireless
Setup Select to setup basic wireless parameters.
SSID -The service set identifier ( SSID ) or network name.
It is case sensitive and must not exceed 32 characters, which may be any keyboard character. You shall
have selected the same SSID for all the APs that will be communicating with mobile wireless stations.
Channel -Select the appropriate channel from the list provided to correspond with your network
settings. You shall assign a different channel for each AP to avoid signal interference.
Security
There are 2 types of security to be selected. To secure your Wireless Networks.
WEP: Make sure that all wireless devices on your network are using the same encryption level and
key. WEP keys must consist of the letters "A" through "F" and the numbers "0" through "9."
WPA:
802.1x:WPA RADIUS uses an external RADIUS server to perform user authentication. To use WPA
RADIUS, enter the IP address of the RADIUS server, the RADIUS Port (default is 1812) and
the shared secret from the RADIUS server.
PSK: Is a special mode of WPA for home users without an enterprise authentication server
and provides the same strong encryption protection.To use WPA Pre-Shared Key, enter a password
in the WPA Shared Key field between 8 and 63 characters long.
|
| |
WAN Settings
WAN Settings are settings that are used to
connect to your ISP. These settings may be referred to as Public settings.
These settings are provided to you by your ISP. Please select the
appropriate option to connect to your ISP.
PVC - Leave the set at the default
value 0 the first time the Router is set up. For more information on this
option see Multiple PVC Operation.
VPI - If instructed to
change this, type in the VPI value for the initial connection (using PVC
0). Default= 8.
VCI - If instructed to change this,
type in the VCI value for the initial connection (using PVC 0). Default= 35.
Virtual
Circuit - The Virtual Circuit over which this PPP data is sent. The
VC identifies the physical path the data takes to reach your
ISP.
Service Category - Select the ATM service category.
PCR - Enter the ATM PCR value.
SCR - Enter the ATM SCR value. |
| |
WAN - Dynamic IP Address
Select this option if your ISP provides you
an IP address automatically. This option is typically used for Cable
services.
Please enter the Dynamic IP information accordingly. |
| |
|
WAN - Static IP Address
Select this option to set static IP information. You will need to
enter in the Connection type, IP address, subnet mask, gateway address, and DNS address(es)
provided to you by your ISP. Each IP address entered in the fields must be
in the appropriate IP form, which is four IP octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this
format. Example:
192.168.0.100
|
| |
|
WAN - PPPoE/PPPoA
Select this option if your ISP requires you to use a PPPoA/PPPoE connection. This
option is typically used for DSL services. Select PPPoA/PPPoE to obtain an IP address automatically
for your PPPoA/PPPoE connection.
Please enter the information accordingly.
|
| |
|
WAN - Bridge Mode
The ADSL Router can be configured to act as a bridging device between
your LAN and your ISP. Bridges are devices that enable two or more
networks to communicate as if they are two segments of the same physical
LAN. Please set the Connection type.
|
|
LAN Settings
These are the IP settings of the LAN
interface for the DSL-G604T. These settings may be referred to as Private
settings. You may change the LAN IP address if needed. The LAN IP address
is private to your internal network and cannot be seen on the Internet.
The default IP address is 192.168.1.1 with a subnet
mask of 255.255.255.0. You may enter a local domain name for the
LAN network if you prefer.
|
| |
DHCP Server
DHCP stands for Dynamic Host Control Protocol. The DHCP
server gives out IP addresses when a device is booting up and request an
IP address to be logged on to the network. That device must be set as a
DHCP client to "Obtain the IP address automatically". By default, the DHCP
Server is enabled. The DHCP address pool contains the range of the IP
address that will automatically be assigned to the clients on the
network.
Starting IP
address - The starting IP address
for the DHCP server's IP assignment.
Ending IP address -
The ending IP address for the DHCP server's IP assignment.
DHCP client computers will have their
information displayed in the Client Table. The Client Table will show the
Host Name, IP Address, MAC Address
each client computer. |
| |
DNS Settings
The DNS Configuration allows the user to set the
configuration of DNS
relay.
DNS relay selection - Choose
Disable DNS relay or Use auto discovered DNS server only or Use user
discovered DNS server only.
Preferred DNS server - Enter the primary DNS server IP address.
Alternate DNS server - Enter the secondary DNS server IP address.
|
| |
Dynamic DNS Settings
Dynamic Domain Name System (DDNS) lets you assign a fixed
host and domain name to a dynamic Internet IP address. It is useful when you are hosting
your own website, FTP server, or other server behind the Router. Before using this feature,
you need to sign up for DDNS service . |